 |
 |
 |
|
 |
|
 |
|
 |
|
 |
|
 |
GMP Cable Blowing Machines Brochure
Cable blowing machine offerings from GMP
Easy to read PDF comparison of GMP's Family of Blowing Machines
more info
Micro Fiber Cable
Blowing Machine
P/N 89010
The "Breeze" micro
fiber cable blowing machine is designed to meet the growing need for
micro fiber cable installation (FTTx).
more info
P/N 89300
The new AirStream cable blowing machine has been designed to maximize protection for micro cables with a compliant double drive concept, backed by the latest technology in servo controls to provide precise control of torque and speed.
more info
Fiber Optic Cable Blowing Machine
P/N 89000
Designed to be
safe, fast and effective, even on tough terrain, the "Tornado" cable
blowing machine will move fiber optic cable into pre-installed innerduct
or direct-buried duct.
more info
P/N 89801
The GMP family of Line Blowing products are designed to be both rugged and economical. Available are a collection of accessories that will allow you to efficiently blow line ranging from 1" innerduct to 5" duct.
more info
P/N 89141
Polywater® Prelube 2000™ reduces frictional drag during the blowing of outside plant cable into duct. It increases the length of cable that can be blown in a single shot.
more info
Metaflux Chain Lubricant
P/N 89153
A fully synthetic, special chain grease for use in lubrication of the Tornado's
drive chain.
more info
Trailer Mounted Cable Fleeter 1/2" x 10,000'
P/N 89016
The Fleeter replaces the manual method of “figure eighting” cable, and provides protection and security for the cable.
more info
Trailer Mounted Fiber Optic
Puller
P/N 70605
The Trailer Mounted Fiber Optic Puller has been designed to exceed the requirements
of installing telecommunication cables, employing a 32" diameter single
capstan to provide a controlled force to the pulling rope or tape.
more info
Capstan Drive
P/N 70329
Gives your mobile hydraulic equipment
the capacity to run our line of power reels and capstans.
more
info
Hydraulically Limited Cable
Puller
P/N 70483
A
cable puller
that offers self-contained pulling power, speedy set up and high production
in an affordable package for cable placing crews.
more info
P/N 15472
GMP offers you a choice of several lightweight aluminum alloy units that mount on a standard 2-7/16 in. (62 mm) diameter drive shaft with either a bayonet or a cross pin type of connection.
more info
P/N 15314
This sheave’s big 15 in. (38 cm) bending radius helps provide easy cable pulling in manhole vaults with any fiber optic cable up to 3/4 in. (19 mm) diameter.
more info
Corner Blocks - 45° and 90°
P/N Various
These rugged and lightweight corner blocks are used to guide cable and evenly distribute the load on the cable when pulling around corners. Available with Polyurethane rollers or Aluminium
more info
P/N 15316
Provides a smoother and safer cable placement in manhole vaults with a minimum of set up time.
more info
P/N 70045
When secured to the pulling irons, will allow you to mount up to two Fiber Optic Quadrants or a single Fiber Optic Split Sheave for ease of cable placement.
more info
Fiber Optic Sheave and Shackle
P/N 71560
"Bicycle
wheel" combination is designed to accommodate the special handling
needs of pulling fiber optic cable.
more info
P/N 53700
Gives you invaluable protection when pulling either fiber optic or coaxial cable.
more info
Innerduct Pulling Eyes
P/N 60510
These rugged chrome-plated steel pulling eyes allow innerduct placement
to become a faster, safer operation.
more info
Ball Bearing Swivels
P/N 70136
These tough swivels are designed to handle higher thrust loads for extra
cable safety and faster straight pulls.
more info
P/N 71130 to 71132
These Stainless Steel connectors maximize usefulness by catering to the same rope capacity and using different ends to attach to the most popular swivel sizes. We also carry a universal rope to rope connector.
more info
P/N 71140 to 71143
The Heavy Duty Connector connects two items with lugs or wire loop fittings. Typical application is to connect a wire mesh pulling grip to the pulling line.
more info
P/N Various
Pulling Grips are indispensable in many different cable pulling applications. Manufactured from high-tensile, galvanized steel wire that is evenly woven in a single, double or triple wire weave according to pulling tension requirements
more info
P/N Various
This convenient product will allow multiple pulls at one time by attaching 2 or 3 cables or ducts to the Puller.
more info
P/N 88900
With GMP’s Trailer Mounted Powered Duct Rod Pusher, hydraulically powers the trailer mounted 1200 ft. capacity,1/2" duct rodder in and out of conduits. One man operation with minimal setup time.
more info
P/N 89004
With GMP’s Powered Duct Rod Pusher and a 1/2” GMP Duct Rodder, the job of placing pulling lines or fiber cables just got that much easier with less personnel in old or occupied conduits.
more info
P/N Various
Made from fiberglass strands impregnated with a highly resilient, thermosetting resin, our Duct Rodders incorporate proprietary strengthening agents that allow GMP to offer a high quality Continuous Duct Rodder at an economical price. Now available with detectable rod.
more info
Find, follow and map detectable duct rod and copper based cables that are located in nonmetallic duct.The RD7000+ is ergonomically designed to deliver a light weight, energy efficient and exceptionally well balanced locator.
more info
The VATS Block and Guide System was designed to support placement of the Multi-Port Terminal Fiber on 1/4 - 3/8 in. (6-10 mm) dia. suspension strand during new construction or while overlashing to existing lashed cable. Wide 4-1/2" rollers on both block and guide, allow for the pass thru of the largest terminal to date.
more info
P/N 70427
The new GMP Power Duct Slitter, designed to be both rugged and economical. Based on a proven design, our slitter will save you both time and effort.
more info
P/N 10900
A mechanically-assisted, hand-operated tool designed to make longitudinal slits in long lengths of innerduct.
more info
P/N 10923
An ingenious tool with a ratcheting design that longitudinally slits the outer sheath of telecom cables
more info
P/N 75984
These spindles are equipped with a Ratchet Binder using a 2" wide web to provide a sturdy, yet temporary, attachment to a pole for FIOS/VATS cable reels.
more info
P/N 70403
These large diameter Reel caddies can be used to support and dispense drop cable quickly and easily. The caddy is lightweight and folds flat for compact storage.
more info
P/N 71669
A tough, easily maneuvered and portable frame that's ideal for supporting any reel up to 36 in. (914 mm) wide x 50 in. (1270 mm) dia.
more info
P/N 07254
A tough frame that's ideal for supporting any reel up to 24 in. wide x 36 in. dia. for easier, smoother payouts.
more info
Expanding Jaw Pulling Eyes
P/N Various
GMP’s line of Expanding Jaw
Pulling Eyes are designed for the installation of 1-1/4” to
14” diameter
Polyethylene Pipe in wall sizes ranging from SDR 9 thru SDR 21 and
Sch 40.
more info
P/N Various
The Double "E-Loc" coupling was designed to join both smooth and ribbed HDPE innerduct, specifically for pneumatic methods of cable placement where air and water-tight integrity of the system is imperative.
more info
P/N Various
These coated aluminum duct couplings are reusable and ideal for both temporary and permanent installations on smoothwall or externally ribbed conduit.
more info
P/N 10912
Best tracking, and easiest cutters available.
more info
P/N 89565
Will cleanly cut micro duct up to 3/4 in. (19mm)
more info
Missiles, Foam and Inflatables
GMP offer three different types of line carriers to meet your specific needs in cable blowing.
more info
|
|
|
|
|
|
Tel: +1.215.357.5500 Fax: +1.215.357.6216 Email: info@GMPtools.com
© 2011 General Machine Products Co., Inc
