 |
 |
 |
|
 |
|
 |
|
 |
|
 |
|
 |
P/N 67262
These plated steel brackets let you temporarily or permanently mount signs, a drop wire hook P/N 06530 and other attachments on steel poles without the inconvenience of on-site drilling.
more info
Drop Wire Hook and Strap
P/N 06530
This galvanized steel wire hook and strap combo is the one to use when
you need to install a drop wire clamp
on masonry, or an unexposed drop wire on a non-masonry surface where porcelain
insulation is not required.
more info
B Drop Wire Clamp
P/N 07380
The wedging action of this aluminum clamp and stainless steel bail
holds most sizes of two-conductor drop wire securely, but without damaging
the wire covering.
more info
P/N 79750
Used with Cable Guards, Cable Spacers, Lashed Cable Supports and a Reinforcing Strap to attach strand and lashed cable to a pole using the suspension bolt where either the upward or downward grade change exceeds 20%.
more info
Discontinued
C Sheave Support
P/N 79752
Used with Cable Guards, Cable Spacers, Lashed Cable Supports and a Reinforcing
Strap to attach strand and lashed cable to a pole using the suspension
bolt where either the upward or downward grade change exceeds 20%.
more info
D Lashing Wire Clamp
P/N 07886
Is perfect for temporary and permanent terminations or
grounds, this all steel clamp lets you securely attach two lashing wires
or #6 ground wire on any size strand from 1/4 in. to 7/16 in.
more
info
P/N 81460
Designed for permanent wire terminations, this clamp has the same hardware, construction and clamping range as our D Clamp (see previous item), but with a one piece stamping formed to let both sides grip the messenger in perfect alignment.
more info
P/N various
When combined with Cable Spacers, these bands help support and stabilize your cable around poles or other obstructions where the messenger and cable separation doesn’t exceed 3-1/4 in. (83 mm).
more info
P/N 74109
Reduce your pole space requirements and installation labor demands with GMP's Extension Bolts and Reinforcing Straps.
more info
P/N 70110
This galvanized pole line hardware was designed to install dead-ends and guys on utility poles already having existing risers that prevent standard attachment practices.
more info
P/N 01340
These rings are the perfect way to keep feeder/distribution cable and jumper wire paths in order and out of the way between distribution terminal blocks
more info
P/N 07385
Use GMP's cable damper to help mitigate large amplitude, low-frequency vibrations that can cause serious cable damage.
more info
P/N 72301
Install these straps and prevent aerial cable from dancing in the wind; possibly causing cable damage
more info
P/N 79283
Our newest pole mounted work platform, the GMP D Cabinet Balcony was designed to accommodate the new generation of fiber optic based cabinets as well as the existing line of cross connect cabinets.
more info
P/N 79281
Our largest pole mounted work platform, the GMP 2000 Balcony was designed to accommodate the larger capacity cross connect cabinets.
more info
These durable 2 ft. (610 mm) long Southern Pine guards come in two (2) different styles to protect lashed or ringed cable from the damge that swaying tree branches can cause.
more info
These 8 in (203 mm) long slit polyethylene tubes are available in four (4) different diameters to help prevent cable sheath abrasion where strand is attached to poles. Standard package 25.
more info
Submarine Splice Case and Clamps
P/N 75662
These are the perfect solution for
rugged protection and covering of splices or repairs in wire-armored
submarine cables.
more info
|
|
|
|
|
|
Tel: +1.215.357.5500 Fax: +1.215.357.6216 Email: info@GMPtools.com
© 2003-2004 General Machine Products Co., Inc
