 |
 |
 |
|
 |
|
 |
|
 |
|
 |
|
 |
B Pressure Testing Gauge
P/N 74700
Getting fast pressure measurement
is easy with this inexpensive 2 in. (51 mm) dia. gauge.
more info
C Pressure Testing Gauge
P/N 77170
This precision gauge's 4
in. (100 mm) is graduated in 0.05 psi increments, and delivers highly
reliable measurements ± 1/2 % anywhere between 0-12 psi.
more
info
C Pressure Testing Pump
P/N 70221
Compact, hand-held pump tests
the integrity of splice cases.
more info
P/N 75530
Helps control gas pressure when using pneumatic tools like a cutter or presser.
more info
P/N 82211
Works with your gas cylinder to control outlet pressure when you're charging cables during pressurization.
more info
B Pressure Regulator
Shackle
P/N 06934
The best and most reliable way to protect your gas cylinder and regulator
more info
B Gas Cylinder
Sling
P/N 07264
For hoisting and transporting 224 cu. ft., 9 in. (22.9 cm)
dia. cylinders of nitrogen.
more info
C Regulator Wrench
P/N 07516
This three-slot wrench makes tightening nuts on almost any cylinder,
hose or gas manifold connection a breeze.
more
info
P/N 76760
Are designed to move gas from a pressure testing regulator to an inlet valve.
more info
D and E Pressure Hose
P/N 76780
Are designed for conveying fuel gas (Acetylene, MAPP or LP) from
cylinder regulators to torches or gas appliances such as heaters or
furnaces.
more
info
Cable Drill
P/N 67970
Let
you make clean cable holes for placing flanges in 1 in. (25.4 mm) dia.
or larger paper or pulp insulated lead or plastic sheath cable.
more
info
P/N 07064
Prevent electrical breakdown from the cable core to the sheath when installing a pressure testing fitting by using this handy tool to separate the core and sheath with strips of muslin.
more info
P/N 06515
This corrosion-resistant bracket will really be appreciated
by the technician working in manhole vaults when
testing pressure.
more info
These ells are specifically designed for soldering 1/4 in. ID lead pipe directly to lead cable sheath. Two configurations are available.
more info
A complete selection of valves and valve hardware for pressure testing.
more info
P/N 74710
An excellent all-around tool for removing or replacing valve cores and preparing valve stems for soldering.
more info
P/N 01233
Helps prevent conductor failure by stopping moisture from being drawn into the cable sheath from the outside.
more info
P/N 06565
Makes an excellent temporary gas pressurizing point, especially when flash-testing individual sleeves.
more info
P/N 77401
Used to secure wrapped joints while splicing plasticsheathed, gas-tight cable, these 3/8 in. (9.5 mm) wide stainless steel clamps come in a variety of sizes to fit all common cable types.
more info
P/N 08669
This combination flange and fitting is ideally suited for use at pressure reading points, bypasses or air inlets at any 3/4 in. (19 mm) dia. or larger cable.
more info
P/N 72411
Is special acid-core wiping solder that is used for soldering lead objects like cable sheath or sleeving.
more info
P/N 04320
Are bundled in 6-lot packages, these 1-1/4 in. (32 mm) dia. x 3-1/2 in. (89 mm) L candles are the easiest way for you to apply stearic acid flux to lead cable.
more info
P/N 82870
Available in either ready-to-use solution or concentrate, this versatile fluid can positively identify leaks in not only lead and polyethylene cable sheath, but air pipe, sleeves, splice cases and fittings.
more info
P/N 07271
The funnel-shaped well in this aluminum can makes it easy to apply our Soap Solution while keeping your working area clean.
more info
P/N 76011
This pliable black butyl rubber material is ideal for building up seal collars and filling cavities in splice cases, or sealing bond clamps, ground conductors and the hardware used in cable splicing.
more info
P/N 08553
Used to seal and pressurize CA-3131 pipe (.710" O.D. and .600 I. D.).
more info
P/N 08664
You can use this valve with 3/8" dia. plastic tubing to build a handy bypass across a pressure plug at an under-ground-aerial cable junction, or on a riser pole.
more info
P/N 07267
Is the one kit to have when pressure testing cable, this comprehensive package combines many of your most important tools into one highly portable case.
more info
|
|
|
|
|
|
Tel: +1.215.357.5500 Fax: +1.215.357.6216 Email: info@GMPtools.com
© 2003-2004 General Machine Products Co., Inc
